DTF Transfer Size Chart and Logo Placement Guide

Most adult full-front designs are 11 to 12 inches wide, placed about 3 inches below the collar. Left chest logos run about 3.5 to 4.5 inches wide. This chart covers every common placement, plus how to measure so your prints land straight.

Mockup of a black t-shirt with a large full-front print reading Chasing Dreams East Salinas

Key takeaways

  • Adult full fronts are typically 11 to 12 inches wide, with the top 3 to 3.5 inches below the collar.
  • Left chest logos are typically 3.5 to 4.5 inches wide, centered 3.5 to 6 inches from the shirt's center.
  • Youth full fronts run about 8.5 to 10.5 inches wide; toddler fronts about 5.5 inches.
  • Hat fronts are about 4 to 5 inches wide and 1.75 to 2.25 inches tall, depending on crown height.
  • Size each design at its real press size before you put it on a gang sheet.

Most adult full-front DTF transfers are 11 to 12 inches wide, with the top of the design about 3 to 3.5 inches below the collar. Left chest logos usually run 3.5 to 4.5 inches wide, and full backs 12 to 13 inches wide. The chart below covers every common spot on a shirt, hoodie, polo and hat, with where each design goes.

These numbers come from apparel decorating suppliers and are starting points. Garment cut, size and your design's shape all affect what looks right, so we also show how to measure.

DTF transfer size chart

Widths are for the design itself, not the garment. Where suppliers differ, we give the range.

PlacementTypical design widthTypical placement
Full front (adult)11 to 12 in. (max area about 12 x 14 in.)Top of design 3 to 3.5 in. below the collar
Center chest / medium front8 to 10 in.Top 2.5 to 3 in. below the collar
Left chest or pocket (adult tee)3.5 to 4.5 in. (max area 5 x 5 in.)5.5 to 9 in. down from the shoulder seam, 3.5 to 6 in. from center
Polo left chest3.5 in.5.5 to 9 in. down from the shoulder seam, 4 to 6 in. from center
Full back (adult)12 to 13 in.Top 2 to 4 in. below the collar
Hoodie or sweatshirt backUp to about 14 x 11.25 in. (adult)Start 4 to 6 in. below the neckline so the hood does not hide it
Upper back / across shoulders12 to 14 in. wide, about 4 in. tallJust below the neckline to about 4 in. down
Back collar / locker patch2.5 to 4 in.1 to 2 in. below the back collar seam
Short sleeve2.5 to 3.5 in.Centered on the sleeve, about 1 in. above the hem
Long sleeve (vertical)2 to 2.5 in. wide, up to 11.5 to 14 in. longRunning down the sleeve, ending about 3.5 in. above the cuff
Youth front8.5 in. (small) to 10.5 in. (medium/large)Top 2 to 3 in. below the collar
Toddler front / left chest5.5 in. / 2.5 in.Top of front design about 2 in. below the collar
Hat front4 to 5 in. wide, 1.75 to 2.25 in. tallCentered on the front of the crown
Jacket backUp to about 14 x 11.25 in. (adult)Design center 6 to 9 in. below the collar seam
Typical DTF and heat transfer design sizes and placements, compiled from Stahls' and Ryonet (screenprinting.com) placement guides. Adjust for garment cut and size.

Sources: the Stahls' Ultimate Guide to Design Size and Placement, Stahls' design placement tips, the Stahls' post on t-shirt design sizes and Ryonet's DTF transfer placement guide.

Front placements: full front, center chest and left chest

Full front and center chest

Stahls' lists a centered adult front at 11 x 11 inches within a 12 x 14-inch maximum area, and Ryonet's standard is 11 x 11 inches, up to 12 inches wide. Both place it about 3 inches below the collar (Stahls' says the top of the design goes 3 to 3.5 inches down). A center chest print is smaller and sits higher: Ryonet lists 8 to 10 inches wide, 2.5 to 3 inches below the collar, and Stahls' "medium front" is 8 x 8 inches.

Left chest

The left chest (on the wearer's left) is the classic logo spot. Stahls' sizes it at 3.5 x 3.5 inches inside a 5 x 5-inch area; Ryonet lists 3.5 inches wide by 2 inches tall, up to 4.5 inches wide.

Placement is where sources differ most. Stahls' ebook says 5.5 to 8 inches down from the shoulder's left seam and 4 to 6 inches over from center, while its placement tips page says 7.5 to 9 inches down for tees and polos. Ryonet measures from the collar: 2.5 to 3 inches down to the center of the graphic, 3.5 to 4 inches from the center line. Pick one method and use it on every shirt in the order.

Mockup of a black polo shirt with a small left chest logo
Example design mockup: a small left chest logo on a black polo.

For polos, Stahls' suggests moving the logo about 1/2 inch farther from center for each size up (3.5 inches on a small, 4 on a medium, 4.5 on a large), placing women's left chest graphics about 1 inch higher than men's, and leaning toward the buttons rather than the armpit when in doubt.

Back and sleeve placements

A full back runs about 12 x 14 inches per both Stahls' and Ryonet, with Ryonet allowing up to 13 x 16 inches for oversized graphics. Stahls' places it 2 to 3 inches below the collar and Ryonet 3 to 4 inches. For an across-the-shoulders name, Stahls' lists a 4 x 14-inch area just below the neckline, and Ryonet a 12 x 4-inch print centered 4 inches down. A small back collar logo runs 2.5 to 3 inches square, 1 to 2 inches below the seam, per Ryonet.

On hoodies, Stahls' suggests starting a back design about 6 inches down from the neckline, or 4 to 4.5 inches below the neck edging with the hood up, then adjusting.

Sleeves leave little room. Stahls' lists a 3.5 x 3.5-inch area on the upper sleeve, and Ryonet a 2.5 x 1-inch print about 1 inch above the hem. For long sleeves, Stahls' sizes an adult vertical print at 2 x 11.5 inches and Ryonet allows up to 2.5 x 14 inches, stopping about 3.5 inches above the cuff.

Youth, toddler and hat sizes

Youth and toddler shirts

Stahls' sizes a centered front at 10.5 x 10.5 inches for youth medium and large, 8.5 x 8.5 for youth small and 5.5 x 5.5 for toddlers, placed 2 to 3 inches below the collar for youth and 2 inches for toddlers. Left chest logos stay at 3.5 inches for youth and drop to 2.5 for toddlers. Ryonet's rule of thumb is to scale youth prints down about 15 to 20%, and to scale up about 15% for XXL and larger shirts, placed 2.75 to 3.75 inches from the collar.

Hats

Hat sizes depend on crown height. Stahls' lists front designs at 1.75 x 4 inches (height by width) for low-profile caps, 2 x 5 for mid-profile and 2.25 x 5 for high-profile. Side designs are about 1 x 2.5 inches (1 x 3.25 on high-profile caps) and back designs about 1 x 2.75 inches.

Mockup of a cream and navy snapback with an embroidered front logo
Example design mockup: an embroidered front logo on a snapback cap.

Those sizes are written for heat-applied decoration. For embroidered hats, we'll confirm the size in your quote.

How to measure placement on a shirt

You need a tape measure and a flat surface. These steps follow the Stahls' and Ryonet guides.

  1. Lay it flat: Smooth the garment on a flat surface with the front facing up and the shoulder seams lined up.
  2. Find the center: Fold the shirt in half lengthwise and pinch a crease at the center, as Stahls' suggests.
  3. Measure down for front and back prints: Measure from the bottom of the collar to where the top of the design will sit.
  4. Measure left chest from two points: Measure down from the shoulder seam (or the collar), then over from the center crease.
  5. Center the design by eye: If it is lopsided, such as bold text on one side, shift it so it looks centered, as Ryonet recommends.
  6. Write it down: Record your measurements and repeat them on every shirt in the order.

Sizing designs for a gang sheet

On a gang sheet, every design prints at the exact size it has on the sheet, so size each one for its placement first. Upload transparent PNGs at print size, at 300 DPI, to the DTF gang sheet builder. Mind the 22-inch width: two 11-inch full fronts will not fit side by side once you leave space to cut them apart, so size them to about 10.5 inches or fill the leftover width with small logos. Our guide what is a DTF gang sheet walks through spacing and layout math, and the gang sheet builder video guide shows each step on screen. When your transfers are ready, read how to apply DTF transfers before you press.

Vinyl Cutz prints DTF gang sheets in-house in Salinas, with local pickup at 838 S Main St, Suite B, or shipping. Questions about sizing? Call or text (831) 540-0287.

Frequently asked questions

What size should a left chest logo be?

Most left chest logos are 3.5 to 4.5 inches wide. Stahls' sizes them at 3.5 x 3.5 inches within a 5 x 5-inch area, and Ryonet lists 3.5 inches wide by 2 inches tall, up to 4.5 inches wide. Youth shirts usually keep the 3.5-inch size, and toddler shirts drop to about 2.5 inches.

How far below the collar does a front print go?

For an adult full-front design, place the top of the artwork about 3 to 3.5 inches below the collar, per Stahls' and Ryonet. Smaller center chest prints sit a little higher, around 2.5 to 3 inches down. Youth shirts use 2 to 3 inches and toddler shirts about 2 inches.

What size design should I use for youth shirts?

For a youth full front, Stahls' recommends about 10.5 x 10.5 inches for youth medium and large and 8.5 x 8.5 inches for youth small, placed 2 to 3 inches below the collar. Ryonet's rule of thumb is to scale adult art down by about 15 to 20%.

What size should a hat design be?

Hat front designs are usually 4 to 5 inches wide and 1.75 to 2.25 inches tall. Stahls' lists 1.75 x 4 inches for low-profile caps, 2 x 5 inches for mid-profile and 2.25 x 5 inches for high-profile caps. For embroidered hats, the size depends on the cap and design, so we'll confirm it in your quote.

How do I size designs on a gang sheet?

Size every design at the exact size you want it pressed, using a size chart for each placement, before adding it to the sheet. Upload transparent PNGs at 300 DPI. Remember the sheet is 22 inches wide, so two 11-inch full fronts will not fit side by side with spacing. Resize them to about 10.5 inches, or fill the leftover width with small logos.

Written by

We print, press and stitch custom apparel, decals and DTF transfers in-house at 838 S Main St, Suite B, Salinas, CA. Questions? Call or text (831) 540-0287.